The 7 Steps of Oil & Natural Gas Extraction

By Dr. C. Mark Pearson, Engineer and President of Liberty Resources

I’ve been an engineer and manager for over 35 years in the upstream oil and gas industry from major oil companies to my current Denver-based company, Liberty Resources, where I am the President. When I talk to my friends and family about my job, I find that most of them don’t understand how the oil and natural gas extraction process works. Everyone talks about fracking, but that’s only one step of a larger process. Check out the 7 steps of oil and natural gas extraction below:

STEP 1: Preparing the Rig Site

The above  ground infrastructure—pads and access roads — are built, setting up the land for the next step: drilling.

STEP 2: Drilling

First the drill rig is brought to the location – maybe 20 or 30 truck loads – and put together. Now It’s time to build the infrastructure necessary to unlock the oil and natural gas trapped more than a mile below the ground. A well is drilled straight down into the ground beneath the pad. The first stage is to drill what is called the surface hole down to a depth of 100 feet below the deepest known aquifer.  A steel casing is then cemented in place so there is no risk of polluting precious water aquifers.

After this the “long hole” is drilled and after reaching a depth about 1000 feet above the underground area where oil and natural gas is trapped, the hole is directionally steered to turn it horizontal and out – maybe another mile or two in distance – following the same rock bed. There’s a phenomenal amount of technology required to keep the hole drilling in the same 10-foot-interval for two miles, but this process allows the well to access oil and natural gas across a longer distance rather than just the energy directly beneath the well pad.

Unlike vertical drilling, horizontal drilling minimizes the impact and scale of aboveground land disturbance by allowing drillers to use only one drill pad for multiple wells instead of multiple pads having a single well each. These technological advancements mean today’s well sites are far fewer in number and also smaller than they used to be just 10 or 20 years ago.

STEP 3: Cementing and Testing

Once the target distance is reached, the drill pipe is removed and steel pipe is pushed to the bottom. This “well casing” is cemented in place. Tests are performed to ensure the pipe is impermeable before any production of natural gas or oil can occur.

STEP 4: Well Completion

Before drillers can tap the oil and natural gas, a perforating gun is typically lowered into the ground and fired into the rock layer in the deepest part of the well, creating holes that connect the rock holding the oil and natural gas and the wellhead.

oil and gas 101STEP 5: Fracking                                                                                            

Now that the first stage of the well is open to the oil and gas rock, it’s time to unlock the oil and natural gas that has been trapped in the rock. Cue fracking. Fracking fluid, which is 99.5% water and sand and 0.5% chemicals – many of which are found in everyday household products – is pumped at high pressure through the perforating holes to create paper-thin cracks in the shale rock, freeing the oil and natural gas trapped inside.

The cycles of Steps 4 and 5 are repeated, gradually working up the hole until all the lateral length of the wellbore has been fracked.  This might be 20 or 30 times – but a process that typically takes only a few days to finish.

STEP 6: Production and Fracking Fluid Recycling

Once fracking is completed, production begins. Oil and natural gas flows up from the well bore and fracturing fluid is then recovered and recycled and used in other fracking operations.

STEP 7: Well Abandonment and Land Restoration

When all of the recovered oil and natural gas has been produced, Colorado law requires that the well is permanently plugged and the land is returned to the way it was before the drilling operations started. The land can then be used for other activities and there is no sign that a well was once there.

Producing Colorado’s oil and gas energy is something that can be done safely while contributing hundreds of millions of dollars to the state’s tax base.

 

Dr. C. Mark Pearson studied mining engineering at the Camborne School of Mines (UK) where he received his BS degree, and later a PhD for his studies on the application of fracking to geothermal energy extraction. He has since worked in the oil and gas industry for over 35 years working projects from Texas to Alaska, from China to Russia, and all around the world.  From 1995-1997, he was a professor in the Petroleum Engineering Department at the Colorado School of Mines. Since becoming a permanent Colorado resident ten years ago, he has been President and/or CEO of three Denver-based oil and gas companies, including his current company, Liberty Resources LLC.  Mark is an avid snowboarder, and four of his five children choose to make Colorado their home.